Saturday, 2015-03-14

sledges(not fix, kludge to be more precise)00:00
mal-Nokius: why are those files missing00:00
mal-does not look good00:00
mal-sledges: do you have any ideas why the /system/lib/hw/ is empty on Nokius system00:02
sledgesbattery went down during flashing?00:02
sledgesof cm00:03
sledgesNokius: can you boot to cm via fastboot boot boot.img from ?00:03
*** vakkov <vakkov!~vakkov@> has joined #sailfishos-porters00:03
Nokiuswill try00:04
sledgesbest practise is to boot cm once before flashing sfos00:04
sledgeson some phone it's imporant for /data partition to be initiated, in your case - catch incomplete flashes ;)00:05
Nokiusboot into cm and I did it before flashing cm00:09
Nokiussfos :P00:09
sledgesare you in cm?00:09
sledgesadb shell and do ls -l /system/lib/hw00:09
Nokiusdevice not found00:11
sledgesenable developer mode00:11
sledgestap 8 times on kernel version in about product00:11
sledgesthen allow usb debugging00:13
sledgesand allow me to sleep ;))00:13
sledgeshave a fun night fellows!00:14
Nokius:) GN800:14
*** faebe <faebe!> has quit IRC (Ping timeout: 244 seconds)00:16
Nokiussledges: not Kernel version it'S Build number ;)00:16
mal-that's what it should contain, but why does it show up as empty in sailfish00:19
mal-check the mountpoints once again while you're using adb00:19
*** M4rtinK <M4rtinK!> has quit IRC (Quit: Odcházím)00:20
mal-although the folders were there even in sailfish00:21
Nokius vs
Nokiusboot and userdata correct00:24
mal-yes, but why do you have only those?00:25
NokiusI have no I idea why did this last summer there some missing :(00:26
mal-I think you should add the same ones as mako and hammerhead have, and boot00:27
Nokiusmodem and persist plus boot00:28
mal-so correct mountpoints for boot, modem, persist, system and userdata00:28
mal-the newer version has more examples
mal-for example maguro has a lot more fixed ones than others00:31
mal-I think it's time for sleep, let's continue tomorrow00:33
NokiusI will add  it and run hybris-hal00:33
*** olafh__ <olafh__!> has quit IRC (Ping timeout: 246 seconds)00:35
Nokiusmal-: thanks gn800:38
*** faebe <faebe!> has joined #sailfishos-porters00:40
Nokiusi don't get my mka hybris error I know it's related with my mountpoints but I double check this now 3 times gist200:50
*** vrutkovs is now known as vrutkovs|away00:53
*** faebe <faebe!> has quit IRC (Read error: Connection reset by peer)00:53
*** trt` <trt`!> has quit IRC (Ping timeout: 245 seconds)00:55
Nokiusokay looks like it was the wrong  ' :D00:55
*** alin <alin!~alin@opensuse/member/ealin> has joined #sailfishos-porters00:58
*** vakkov <vakkov!~vakkov@> has quit IRC (Ping timeout: 255 seconds)01:04
Nokiuswith new hybris-boot.img still
*** trt` <trt`!> has joined #sailfishos-porters01:12
Nokiusout put from test_hwcomposer ends with (for new and old build ot it)01:21
Nokiusgn8 THANKS for the help :D01:21
klopsi-u3n8 Nokius01:27
*** vakkov <vakkov!~vakkov@> has joined #sailfishos-porters01:45
*** vakkov <vakkov!~vakkov@> has quit IRC (Ping timeout: 245 seconds)02:07
klopsi-u3so do we hope to make a free os02:36
klopsi-u3one that isnt spied on by intelligence agencies?02:37
*** Lipevakala_ <Lipevakala_!> has quit IRC (Ping timeout: 250 seconds)02:43
*** Lipevakala <Lipevakala!> has joined #sailfishos-porters02:45
*** Tassadar <Tassadar!> has quit IRC (Ping timeout: 264 seconds)03:00
*** vakkov <vakkov!~vakkov@> has joined #sailfishos-porters03:05
klopsi-u3funny how there are no video games about killing americans03:22
*** iTune <iTune!~PhompAng@> has joined #sailfishos-porters04:12
*** electrolux <electrolux!> has joined #sailfishos-porters05:53
*** olafh__ <olafh__!> has joined #sailfishos-porters06:02
*** harha <harha!> has joined #sailfishos-porters06:24
*** beidl <beidl!> has joined #sailfishos-porters07:24
deztructormal-: where do you take configuration from (I am about old versions of packages, e.g. cor)? and for copying - it copies files into the right place while mb2 maybe uses incorrect values and doesn't use BUILDROOT as source root, nor sets it07:26
*** Lipevakala <Lipevakala!> has quit IRC (Quit: IRC for Sailfish 0.9)07:44
carepackmorning nokius!07:50
Nokiusah I missed it again I had to mount /sytsem manually07:54
*** Nokius_ <Nokius_!> has joined #sailfishos-porters07:58
*** Nokius|jolla <Nokius|jolla!~Nokius|> has quit IRC (Ping timeout: 246 seconds)07:59
*** Nokius <Nokius!> has quit IRC (Ping timeout: 265 seconds)08:02
*** Nokius_ is now known as Nokius08:11
Nokiuscu later [afk-life :(]08:11
*** yacuken <yacuken!~yacuken@> has joined #sailfishos-porters08:21
locusfmorning all08:22
*** yacuken <yacuken!~yacuken@> has left #sailfishos-porters08:22
*** corecomic <corecomic!> has joined #sailfishos-porters08:43
*** Lipevakala <Lipevakala!> has joined #sailfishos-porters08:43
Stskeepsmorn sledges08:46
sledgesklopsi-u3: you get a warning for political incorectness on the channel08:46
*** Nokius|jolla <Nokius|jolla!~Nokius|> has joined #sailfishos-porters08:48
sledgeslocusf: how's sony coming together?:)08:48
locusfsledges: not too well for 2 weeks now08:48
locusfsledges: seems that hybris init isn't executed at all08:48
locusfno the ramdisk init08:51
Stskeepslocusf: try in this order: get boot.img from working cyanogenmod/aosp you've flashed, then boot.img with hybris-boot ramdisk, then boot.img with your own kernel + hybris-boot ramdisk08:53
sledgeslocusf: does their stock ship ramdisk in boot.img?08:54
carepackmorning sledges, stskeeps, locusf08:54
locusfsledges: yes08:54
locusfStskeeps: ok will try, was just studying this custom kernel which ships a working ramdisk to study that08:54
sledgeslocusf: busybox doesnt start?08:54
locusfsledges: yeah, at least it doesn't seem that it does, I have added a command to start a green led right at the top of the hybris-boot init script but I can't see it light up08:56
*** Nokius|jolla <Nokius|jolla!~Nokius|> has quit IRC (Ping timeout: 246 seconds)08:56
locusfsledges: also jerpelea encountered a kernel stack trace when using tianchi08:56
sledgeslocusf: lsusb iSerial?08:56
locusfthis happens when mount is triggered inside hybris init08:57
locusfsledges: nothing in lsusb or dmesg08:57
sledgesuart possible?08:57
locusfsledges: jerpelea has uart for tianchi, not possible for my aries afaik08:59
Stskeepswhat SoC?08:59
Stskeepslocusf: selinux=0?08:59
sledgeslocusf: ok, but if problem is the same, kernel uart log is what u need08:59
locusfStskeeps: yes08:59
locusfStskeeps: msm897409:00
Stskeepstry in that order for sure..09:00
*** r0kk3rz <r0kk3rz!> has joined #sailfishos-porters09:00
Stskeepsalso look for spooky alignment kernel options09:01
*** jvb <jvb!jvb@> has quit IRC (Quit: /dev/backer)09:03
*** jvb <jvb!jvb@> has joined #sailfishos-porters09:03
*** louisdk <louisdk!> has joined #sailfishos-porters09:10
locusfhmm with aosp kernel and hybris-boot init it worked09:18
locusfso there was something wrong with the kernel then09:19
*** alin_ <alin_!> has joined #sailfishos-porters09:20
locusfStskeeps: thanks for the tip, continuing now09:23
*** alin <alin!~alin@opensuse/member/ealin> has quit IRC (Ping timeout: 250 seconds)09:24
alin_sledges: hi09:25
*** Tassadar <Tassadar!> has joined #sailfishos-porters09:25
alin_sledges: what was the telnet address?09:25
*** Lipevakala <Lipevakala!> has quit IRC (Remote host closed the connection)09:25
*** Lipevakala <Lipevakala!> has joined #sailfishos-porters09:26
*** alin <alin!~alin@opensuse/member/ealin> has joined #sailfishos-porters09:29
*** alin_ <alin_!> has quit IRC (Ping timeout: 256 seconds)09:30
mal-deztructor: I just cloned the nemomobile github repos, cor from here
mal-locusf: which device?09:40
locusfmal-: sony aries09:40
locusfz3 compact09:40
sledgesmal-: checked branches?09:42
sledgesalin: or .1509:43
mal-sledges: that only has master and staging09:43
*** Nokius|jolla <Nokius|jolla!~Nokius|> has joined #sailfishos-porters09:44
mal-I build all the packages the way packages are normally built in hadk09:44
locusfhmm switch_root command only prints out usage information in hybris initramfs09:45
alinsledges: of course I am in09:46
alinsledges: debugging the failure of the developper mode09:46
alinsledges: we had it before and you fixed it09:46
alinsledges: is the store issue09:46
*** gogeta <gogeta!> has joined #sailfishos-porters09:50
*** louisdk <louisdk!> has quit IRC (Ping timeout: 246 seconds)09:50
sledgesalin: does dtore work?09:51
sledgesalin: store doesnt work due to missimg bit in .ks...09:52
*** electrolux <electrolux!> has quit IRC (Quit: Leaving.)09:52
sledgesalin: start yoir engines, we'll put fingerterm bacl too :D09:52
alinsledges: yes store works...09:53
alinsledges: but nothing command line09:53
sledgesalin: what? how? ssu lr09:53
alinsledges: ssu lr orks09:53
alinsledges: pkcon refresh no09:53
alinzypper se no09:53
alinasks for credentials09:53
sledgesmal-: edit version inside cor/rpm/*.spec manually09:54
sledgesto match the tag. it's the bad thing of mb209:54
sledgesalin: if store works, then pkcon install jolla-developer-mode09:55
sledgesalin: devel-su -p09:55
sledgesfor pkcon refresh to work09:55
sledgesbut i guess you're already root...09:55
mal-sledges: I did, and cor installs ok and is detected ok, but statefs is the problem now09:56
alinsledges: I am root already09:56
locusfStskeeps: sledges: I had no reason to suspect bad kernel since it booted just fine with jerpeleas tianchi09:56
sledgesalin: this means store doesn't work - you won't be able to download/install an app :P if it lists apps doesn't mean it works ;)09:56
sledgesmal-: soz, skipped some backlog09:56
alinsledges: just installed owncloud09:56
alinand uninstalled09:56
alini see something strange in my repo list09:57
sledgesalin: you still need correct adaptation0 for commandline things to work09:57
alinsledges: yap09:57
alinsledges: so which oneis the right one09:57
*** piggz <piggz!> has joined #sailfishos-porters09:57
sledgesalin: means store guys relaxed the check on repo names09:57
mal-sledges: this error
sledgeswhich is good news, i wonder if anyone with a previously-jolla-store-non-working device could check the store too09:58
sledgesmal-: waterhell: -- Up-to-date: /home/mal/rpmbuild/BUILDROOT/statefs-0.0.0-1.arm/lib/systemd/system/statefs-system.service09:59
mal-sledges: could be remnants of a previuos build, it does not clean that10:00
alinsledges: strange there is ssu dr in ks10:00
mal-I removed it once and did not fix anything10:00
alinsledges: now works... interesting... do you think vgrade used a diffeerent thing to build v8 rathen than the script?10:01
sledgesalin: yes10:01
sledgesmal-: mb2 and clean are not friends, git clone :(10:02
sledgesexperienced myself recently10:02
mal-I tried clean already, I'll do git clone also10:02
sledgeswell it's more than make clean (maybe mb clean would work? note, not mb2), as there's also installroot/ - rm that?10:03
sledgesi poked around, but wasn't conclusive, to achieve incremental builds10:03
alinsledges: ok developer mode enabled10:03
sledgesalin: brilliant, we need a new image ;)10:03
alinsledges: we shall close the bug for the next version10:03
alinsledges: yap I will create one on monday or on tuesday10:04
alinping me10:04
sledgesalin: for fingerterm10:04
sledgesalin: perfect, i'd hope to get camera in by then ;)10:04
alinsledges: perfect10:04
alinI also fixed my screen last night10:04
sledgesbut no promises10:04
alinn5 back to life10:04
sledgesalin: wow congrats, hairdrier?10:04
alinsledges: yes10:05
alinsledges: and a new screen... but to be honest I did not think I will make it...10:05
alinthe screen is just a collection of thin plastic things10:05
alinthe most complicated was to put the frame back glued my finger10:06
sledgesi did for for friend's htc, started collecting dust under itself, and black patches appeared eventually (after a drop peharps)10:06
sledgestell me about it:D10:06
sledgeswhy do they use glue, could just do with rubber seal and latches, screws10:07
mal-sledges: interesting, when running mb clean rpm/statefs.spec I get rm: cannot remove `/home/mal/rpmbuild/BUILD/statefs': No such file or directory10:07
alinsledges: no idea... maybe chinese kids like glue... you know can be sniffed10:07
mal-the built stuff is in /home/mal/rpmbuild/BUILDROOT/10:07
sledgesalin: you get a warning for inapropriatetness10:07
sledgesthat's a second warning already10:08
sledgesmal-: mb2 vs mb,, better no mess10:08
mal-mb2 does not have clean10:09
alinsledges: i hope about the glue sniffing... as the first is a fact10:09
sledgesmal-: is what i said10:09
alinsledges: fingerterm10:09
mal-sorry, too much stuff in backlog10:09
sledgesalin: you're not helping10:09
sledgesthis is an international channel and any indecency will not be tolerated10:10
sledgesalin: fingerterm is ready since 2 months, if taken from obs (as your script will):
mal-sledges: I now remove the rpmbuild folder and cloned a clean statefs10:12
mal-sledges: still the same failure10:13
alinsledges: thought we pushed it into the dhd repo with the rest10:14
sledgesmal-: is it on master and the top commit is tagged?10:14
sledgesalin: that's exactly what happened10:14
mal-sledges: it's master but I don't know how to check for tags10:15
*** piggz <piggz!> has quit IRC (Ping timeout: 244 seconds)10:15
alinsledges: yap... ok... I see vgrade did not use it for alpha810:15
sledgesmal-: github webui releases tab is convenient10:16
*** rusty88 <rusty88!> has joined #sailfishos-porters10:17
mal-it seems that .spec version is not updated10:18
*** Tassadar <Tassadar!> has quit IRC (Quit: Segmentation fault)10:18
*** Tassadar <Tassadar!> has joined #sailfishos-porters10:18
sledgesmal-: refresh10:18
sledgesi just cleaned up10:18
alinsledges: good... now works10:20
alinsledges: I will need to build new dhd we sync on monday about10:20
alinsledges: also I added a new bug10:20
sledgesmal-: hmmm unsure what's up, try building that statefs against sfos-1.1.2 target on Mer OBS10:22
sledgesas it builds fine internally against devel10:22
mal-I have no idea how OBS works10:23
alinsledges: the sensors stuff is all released? I will need no magic10:23
sledgesmal-: you will soon;)10:24
sledgesalin: you'll need loads of magic, sadly10:24
sledgesmal-: it will ease your release process once you have something like
sledgesfor iyokan10:25
alinsledges: merdre...10:25
sledgesmal-: login into the obs and create a project10:25
alinsledges: gps now... long time ago... I remember was a discussion about releasing some glue for gps10:26
alinwhat happened?10:26
sledges(i suggest to create subprojects one-by-one: home:mal:hw:sony:iyokan)10:26
mal-does it need a new account?10:26
sledgesalin: under the carpet10:26
sledges(busy Carsten;)10:26
sledgesmal-: use mer bugzilla credentials10:26
mal-ok, seems like I just had typo in password10:27
alinsledges: sping is comming so maybe the carpet needs some airing... so comes again in view10:27
sledgespeople usually bash the carpets, but i wouldn't go that far:)10:28
mal-sledges: I have now the subproject setup10:30
sledgesmal-: next you'll have to branch statefs10:31
sledgesyou have two options10:32
sledgesrolling and non rolling10:32
sledgesrolling will be webhooked, and each tag on github will trigger its rebuild on your home repo automagically10:32
sledgesup to you10:32
*** gogeta <gogeta!> has quit IRC (Ping timeout: 265 seconds)10:32
mal-which would you recommend?10:32
*** Tassadar <Tassadar!> has quit IRC (Quit: Segmentation fault)10:33
mal-rolling does not sound too bad for me10:33
sledgeswhether you want to stay in control, or accept every release from deztructor (which is good during active development, but may start breaking things when deztructor focuses on some other hardware and you'll forget you had a webhook triggered and will wonder why something broke)10:34
mal-ok, so there is some easy way to force build manually then10:35
sledgeslet's keep that simple for beginning10:35
mal-then non-rolling just in case10:35
sledges"Branch existing package"10:37
sledgesenter nemo:devel:mw10:37
sledgesand statefs in another field10:37
sledgesCreate branc10:38
sledgesI usualy remove the "_link" file10:38
mal-I assume I add the Stay on current revision, don't merge future upstream changes automatically10:38
sledgesclick on _service file and adjust hash to HEAD10:39
sledgesyeap ok, probably that's what adds _link ;)10:39
sledgesmal-: btw, i found a shortcut: statefs build succeded:
sledgesso blame it on mb2 (or we'll see first how it builds against sfos-1.1.2)10:40
sledgesdon't take rpm from nemo:devel as that might cause api/abi breakage on your sfos10:41
mal-i cannot find the _link anymore10:42
sledgesno worries10:42
alinsledges: ok... pulse is cracking from time to time... and takes 35% of cpu when playing10:43
alinI remember was only 20% in earlier days10:43
mal-now I assume I add build targer10:43
sledgesmal-: Repository10:43
sledgesalin: ping jusa_10:43
sledgesalin: streaming radio?10:44
sledgesalin: or mediaplayer too?10:44
mal-sledges: which one of those?10:44
sledgesmal-:  pick one via advanced interface.10:45
alinsledges: mediaplayer... for radio i need to find a station.. bcc shutdown the open streams10:45
sledgesmal-: sailfishos:
sledgesmake sure you pick it from combo box10:45
sledgeslbt: could we have sailfishos:1.1.2.x pls?10:45
sledgesalin: ok, then it's disconcerting10:46
alinsledges: the usage or the cracking10:46
mal-so without armv7hl?10:46
alinsledges: now the cracking stopped10:46
sledgesmal-: yes10:47
sledgesalin: anything10:47
sledgesmal-: name: latest_armv7hl10:47
sledges(as well as repository)10:47
sledgesmal-: check  armv8el only10:47
mal-why armv8el?10:48
sledgeslong story ;)10:48
sledgesalso because there isn't v7hl10:48
sledges(as that's what it is)10:48
sledgesmal-: see the error?10:49
sledgesknow what to do? ;)10:49
mal-will try10:49
* sledges pats mal- on a back10:52
mal-that was just cor, but at least that, statefs is still building10:53
sledgessuccess #210:53
* sledges kicks mb210:54
sledgesand sets it on fire10:54
sledgesclick on sailfishos_1.1...10:54
sledgesin the building box10:54
sledgesgo to download repository10:54
sledgescopy its URL10:55
sledgesgo to your device10:55
sledgesssu ar statefs URL10:55
sledgeszypper ref statefs10:55
sledgeszypper dup --from=statefs10:55
alinsledges: 40% now but this song is better deserves all the cpu cycles it needs10:57
mal-sledges: I'll need to add additional package statefs-providers10:58
alinmal-: which device do you break?10:58
sledgesgo ahead, #upstreamallthethings :D10:58
* sledges afk a bit10:59
mal-alin: iyokan10:59
alinmal-: and in english?11:00
mal-xperia pro11:01
mal-sledges: nothing provides pkgconfig(qtaround-dbus) >= 0.2.4, I can't find anything branch that from11:03
alinsledges: shall I report the high usage for pulse?11:04
mal-sledges: actually found from mer-core:devel11:05
alinsledges: ok... the cracking appears only when I move the phone....11:05
alinsledges: maybe sensors related11:05
sledgesalin: docu;ent all that in a bug pls11:12
locusfsledges: any tips about switch_root printing out usage info instead of switching root?11:13
sledgeslocusf:  i had that somewhere11:13
sledgesparameter conflict,  different busybox version?11:14
locusf1.22.1 static11:14
mal-sledges: installed ok11:14
sledgesput all cmdline switches to bare minimum11:14
sledgesmal-: \/o11:14
mal-however battery status is not working11:14
sledges(lol this typo actually looks like clapping:)11:14
sledgesmal-: now you're on bleeding edge, deztructor can help immediately;)11:14
mal-yes :)11:15
sledgesuntil then - happy debugging;D11:15
*** rusty88 <rusty88!> has quit IRC (Quit: Konversation terminated!)11:15
*** OrokuSaki <OrokuSaki!470bf285@gateway/web/freenode/ip.> has joined #sailfishos-porters11:23
OrokuSakiI have this error running mb2 creating the rpm's... something to do with repo and git... I deleted my user11:24
OrokuSakirecreated the user, and started over...same error...
OrokuSakianone know what that is???11:25
OrokuSakiGuess I need to add a manifest for my device?11:25
locusfmine switch_root just causes to reboot11:27
sledgeslocusf: how did you solve kernel problem before?11:30
sledgeslocusf: strace?:)11:30
locusfsledges: I have no idea, probably because of wrong base platform version (master vs. l-mr0 branch)11:30
locusfsledges: well how do ya strace in busybox init?11:31
OrokuSakiyup that is it11:31
*** Tassadar <Tassadar!> has joined #sailfishos-porters11:32
mal-sledges: it seems building both statfs and statefs-providers with mb2 is broken11:35
sledgeslocusf: compile strace statically?11:36
mal-I tried to see if I could build statefs-providers11:36
mal-which is needed for hacking11:36
sledgeslocusf: just add debug info to switch_root11:36
locusfsledges: okay11:36
sledgesmal-: you'll have to rely on obs sadly, lengthier process, also fork repo to your github home and adjust _service11:37
sledgesmal-: also ask guys on #mer about mb2 breakage ( i guess deztructor tried to mb2 it as well)11:37
*** piggz <piggz!> has joined #sailfishos-porters11:37
mal-deztructor: this on journal log when starting statefs with power-udev
locusfhmm it seems that the usage message is good to show up when running manually11:47
locusfits not from pid 111:47
locusfso its ok11:47
locusfbut something else is wrong and I don't know what it is, apparently switch_root just dies after booting to it and device reboots11:48
mal-deztructor: debug output from statefs
*** alin <alin!~alin@opensuse/member/ealin> has quit IRC (Ping timeout: 240 seconds)11:52
*** alin <alin!~alin@opensuse/member/ealin> has joined #sailfishos-porters11:53
*** piggz <piggz!> has quit IRC (Ping timeout: 252 seconds)11:54
OrokuSakistrange... it gave me a parse error, but then I realized I was inside of vi =) finally11:54
sledgeslocusf: selinux=0 in cmdline11:57
sledgesmight be some flags too re that11:57
locusfsledges: no help :/12:02
mal-deztructor: I also tried CUTES_DEBUG=1 contextkit-monitor /run/state/namespaces/Battery, it gives only "Error accessing property" fro everything12:08
*** alin_ <alin_!> has joined #sailfishos-porters12:08
*** alin <alin!~alin@opensuse/member/ealin> has quit IRC (Ping timeout: 264 seconds)12:09
OrokuSakirest of middleware
*** plfiorini <plfiorini!> has quit IRC (Ping timeout: 272 seconds)12:32
*** BluesLee_ <BluesLee_!> has joined #sailfishos-porters12:33
BluesLee_sledges: same issue here with audio
sledgesBluesLee_: awesome, can alin_ or you add this to the bug pls?12:37
alin_BluesLee_: do you have an account?12:38
mal-sledges: I have trouble getting proper debug output from statefs, it is using for output12:39
*** vrutkovs|away is now known as vrutkovs12:39
alin_BluesLee_: and you are right only with the screen on12:39
mal-or maybe it's just not printing stuff12:39
alin_BluesLee_: do you have high usage too of cpu?12:40
*** zhxt_ <zhxt_!~zhxt@> has joined #sailfishos-porters12:40
alin_BluesLee_: and by the way all you need for mp3 is gat-av installed...12:40
alin_did I read well than in feb release one shall be able to customize parts of theme?12:41
mal-ok, looks like it is not even using power-udev12:43
*** BluesLee_ <BluesLee_!> has quit IRC (Ping timeout: 264 seconds)12:44
*** vrutkovs <vrutkovs!vrutkovs@nat/redhat/x-gjfuuumfkjiqjndx> has quit IRC (Read error: Connection reset by peer)12:45
*** vrutkovs <vrutkovs!vrutkovs@nat/redhat/x-qseyenrnwilvhrlp> has joined #sailfishos-porters12:45
*** Tassadar_ <Tassadar_!> has joined #sailfishos-porters12:49
*** Tassadar <Tassadar!> has quit IRC (Remote host closed the connection)12:51
*** alin_ <alin_!> has quit IRC (Quit: Konversation terminated!)13:17
*** vakkov <vakkov!~vakkov@> has quit IRC (Read error: Connection reset by peer)13:18
*** vakkov <vakkov!~vakkov@> has joined #sailfishos-porters13:19
*** BluesLee <BluesLee!> has joined #sailfishos-porters13:20
BluesLeeissues with irc client and wireless connection13:20
BluesLeesledges: this was an observation from a user, i wanted to countercheck that last week but was not able to install any package with alpha8, store is also broken13:21
BluesLeesledges, alin: i can boot my N5 but someone should tell me how to fix the issue with installing packages13:21
BluesLeesledges: how to restart sensors? rotation stopped working13:21
*** zhxt_ <zhxt_!~zhxt@> has quit IRC (Ping timeout: 264 seconds)13:22
sledgessledges: systemctl --user restart sensorfw13:22
sledgesBluesLee: ^13:22
*** zhxt_ <zhxt_!~zhxt@> has joined #sailfishos-porters13:22
BluesLeesledges: should i expect any services within /etc/init.d?13:25
BluesLeesledges: nothing there:-)13:27
r0kk3rzBluesLee: it uses systemd13:28
*** faebe <faebe!~androirc@> has joined #sailfishos-porters13:28
BluesLeer0kk3rz: thanks13:29
BluesLeeswitching between the mediaplayer and the terminal crashs the sensors somehow13:31
*** OrokuSaki <OrokuSaki!470bf285@gateway/web/freenode/ip.> has quit IRC (Ping timeout: 246 seconds)13:36
*** BluesLee <BluesLee!> has quit IRC (Quit: IRC for Sailfish 0.9)13:38
*** faebe <faebe!~androirc@> has quit IRC (Read error: Connection reset by peer)13:41
r0kk3rzshould I have a copy of droid-hal-configs github checked out?13:48
r0kk3rzmaybe i missed a step...13:48
*** iTune <iTune!~PhompAng@> has quit IRC (Read error: Connection reset by peer)13:53
r0kk3rzbecause i found this: <<13:59
r0kk3rzwhich seems to have configs for vivo14:00
r0kk3rzwhich is probably just a copy of piggz's hacks from the ace14:01
*** iTune <iTune!~PhompAng@> has joined #sailfishos-porters14:06
*** gogeta <gogeta!> has joined #sailfishos-porters14:09
*** OrokuSaki <OrokuSaki!470bf285@gateway/web/freenode/ip.> has joined #sailfishos-porters14:12
OrokuSakihaving a hell of a time using zypper on my device, and I disabled my adaptation0 repo... I can ping google... any advice?14:12
OrokuSakineed to run strace14:12
OrokuSakiit says unexpected error... contact opensuse =)14:13
mal-can you run any zypper commands successfully?14:14
OrokuSakizypper search works14:15
OrokuSakiactually I spoke to soon14:16
OrokuSakiincreasing verbosity14:18
OrokuSakiNot ready to read within timeout.14:20
OrokuSakibefore that is unexpected exception14:20
OrokuSakisometimes repo works and sometimes it doesn't... strange14:20
OrokuSakimaybe it is the firewall rule...14:20
OrokuSakiI can ssh to a public server14:28
*** zhxt_ <zhxt_!~zhxt@> has quit IRC (Quit: Konversation terminated!)14:36
*** arcean <arcean!> has joined #sailfishos-porters14:41
*** gogeta <gogeta!> has quit IRC (Ping timeout: 256 seconds)14:50
*** Nokius|jolla <Nokius|jolla!~Nokius|> has quit IRC (Ping timeout: 246 seconds)14:52
*** photonix <photonix!4df36355@gateway/web/freenode/ip.> has joined #sailfishos-porters14:57
photonixHi all! I used beta 3 sailfish os for mako (nexus 4). When i play youtube video or online music in browser, i get close it! How to solve this problem?) Thanks!14:57
OrokuSakianyone have the link to the jolla repo?15:10
OrokuSakiseems like the repo url's are missing in my etc/zypp15:12
sledgesr0kk3rz: configs are in hybris/15:17
r0kk3rzsledges: yeah i found them, thanks15:18
*** vakkov <vakkov!~vakkov@> has quit IRC (Ping timeout: 265 seconds)15:18
sledgesphotonix: crashes immedately? that needs coding. you could help by filing bug first;)15:18
Nokiussledges: does it look better now test_hwcomposer? did you saw the gist from last night15:19
*** vakkov <vakkov!~vakkov@> has joined #sailfishos-porters15:19
OrokuSakiif I remove all the repo's and add one from the internet.. zypper works15:22
OrokuSakissu related?15:22
OrokuSakinot sure what that is15:22
mal-quite odd the error I get: cat: /run/state/namespaces/Battery/Capacity: Cannot allocate memory15:22
*** piggz <piggz!> has joined #sailfishos-porters15:24
r0kk3rzis it supposed to mount all its filesysytems to my pc on boot?15:30
r0kk3rzthats something different though, which means progress!15:31
r0kk3rzrndis seems to be working too, thanks piggz for the fix15:32
mal-r0kk3rz: yes, in init the filesystems get mounted but not after "continue"15:32
r0kk3rzis that why its taking time to boot15:33
piggzr0kk3rz: it tool me a while to get a hang of the whole boot/debug/continue thing15:33
r0kk3rzbecause its waiting on me to do something...15:33
mal-r0kk3rz: if you are using hybris-recovery kernel15:33
piggzyou need to telnet in and see what it is doing15:33
r0kk3rzwoo im in telnet15:34
mal-dmesg on your computer should show what is the current status of boot process15:34
r0kk3rznow what15:34
Nokiusmal-: hi15:34
piggzr0kk3rz: read the instructions :)15:34
piggzcut n paste the 'continue' line to continue the boot15:34
piggzthen, telnet in again on port 232315:35
mal-r0kk3rz: I would first check that /target is mounted correctly, just to be sure15:35
piggzand watch the output from journalctl -f15:35
mal-Nokius: hi15:35
r0kk3rztarget has stuff in it15:35
mal-good, then continue15:35
r0kk3rznow its rebooted into recovery15:37
Nokiusmal-: build runs and fastboot boot new hybris-boot.img had to mount system manualy test_hwcomposer ends now with this
piggzr0kk3rz: if you take too long it reboots15:38
*** Nokius|jolla <Nokius|jolla!~Nokius|> has joined #sailfishos-porters15:38
r0kk3rzoh right15:38
r0kk3rzyou need to get into the telnet, that wasnt working for me15:38
r0kk3rztry and try again15:38
OrokuSakissu seems to have a problem for me... running something called pkcon repo-set-data jolla refresh-now true15:39
piggzyou need to 1) boot. 2) telnet in on :23 3) do the echo continue command 4) telnet in on 2323 5) continue once more15:39
OrokuSakifatal error can't access given url15:39
mal-r0kk3rz: you can look at usb-messages in dmesg to see what is happening after continue15:39
OrokuSakiOn a 3.0 kernel now as well with cm1115:39
OrokuSakifor some reason dhcp assigns usb0 to 192.168.0.x even though it is on 192.168.2.x15:40
OrokuSakiand i have to change it, in windows, if for some reason you are doing that, subnet mask is not
OrokuSakiuse nmap15:41
mal-ifconfig works fine for that, I have to do it everytime15:42
locusfhas anyone had problems with post switch_root telnet not appearing and device rebooting?15:42
OrokuSakisomeone help me with freakin zypper! PLEASE15:42
r0kk3rzlocusf: that seems to be what im seeing at the moment15:42
r0kk3rzbut its possibly me not knowing what im doing15:43
Nokiusmal-: I added a interface in may network config for that15:43
mal-Nokius: ok15:43
locusfr0kk3rz: you're doing fine so far if you got telnet on kernel initrd :)15:44
r0kk3rzgetting there15:44
mal-OrokuSaki: what does zypper lr tell?15:44
locusfr0kk3rz: tool me two weeks already15:44
r0kk3rzyeah its been on and off for a couple of weeks by now15:44
mal-it took me two month to get display working :)15:45
Nokiusmal-: iirc I set last summer also forwarding rules ( you can find it in the mer wiki)15:45
mal-Nokius: no need, this manual way works fine for me15:46
mal-I basically have to do it once per day15:46
spiiroinreview/testing appreciated nemo#79715:47
spiiroin^ mal-: this basically the patch you already tested15:47
*** OrokuSaki <OrokuSaki!470bf285@gateway/web/freenode/ip.> has quit IRC (Ping timeout: 246 seconds)15:47
Nokiusmal-: any idea what I can test now?15:48
mal-spiiroin: yes, it work for me at least15:48
mal-spiiroin: have you thought about how to make the available field change also?15:49
mal-Nokius: do have the correct content in /system/lib/hw now?15:51
Nokiusmal-: looks now like this
mal-what fixed it?15:53
mal-Nokius: do you still have to mount /system manually? do you start droid-hal-init after that manually?15:53
Nokiusmal-: adding /system to mountfix I assume Yes I had to add it manually15:54
Nokiusmal-: will start droid-hal-init15:54
mal-Nokius: check what is the current status of droid-hal-init first15:55
Nokiusmal-: tolat but logcat is showing a lot "action"15:55
r0kk3rzyeah i think i have the same as you locusf15:56
r0kk3rztelnet doesnt seem to show15:56
r0kk3rznothing is going on in dmesg15:56
*** photonix <photonix!4df36355@gateway/web/freenode/ip.> has quit IRC (Quit: Page closed)15:56
locusfr0kk3rz: I fixed it by replacing correct initscript to /init-debug15:56
r0kk3rzoh right, that command in shows you15:56
spiiroinmal-: that is a bit bigger issue, so I thought I get this clear error out of the way 1st15:57
Nokiusmal-: logcat output
mal-spiiroin: sure15:58
Nokiusmal-: ctrl+c droid-hal-init looks like it hangs getting a Sensor ?15:59
mal-Nokius: you should start the service not run it manually16:00
r0kk3rzstuck again.... right got into the second telnet and hit continue again, what do after that?16:01
Nokiusmal-: oky dummy me16:01
r0kk3rzseemed to reboot after a short while16:01
Nokiusmal-: systemctrl *?* droid-hal-init which option is it systemd noope16:02
Nokiusmal-: How do I check if its running btw?16:02
mal-systemctl restart droid-hal-init16:02
mal-with status as second parameter16:03
mal-no first parameter16:03
r0kk3rzah i see now, watch everything break on journalctl16:06
mal-Nokius: run first systemctl unmask droid-hal-init16:06
mal-Nokius: check journalctl -a output16:09
Nokiusmal-: will doe16:10
r0kk3rzMar 14 15:21:41 Jolla systemd[1]: Timed out waiting for device dev-block-platform-msm_sdcc.2-by\x2dnum-p25.device.16:12
mal-spiiroin: btw, I don't know how this started but now, if I open the keyboard it turns the display on and when I close it turns off the display, unfotunately after that that's the only way to turn display on16:12
r0kk3rzMar 14 15:21:41 Jolla systemd[1]: Dependency failed for Droid mount for /system.16:12
r0kk3rzi assume this is bad16:12
r0kk3rzmaybe one of my mount points is configured wrong16:12
mal-looks like it16:13
Nokiusmal-: is there a tail option its quit full have to go true 2 h now of log16:13
mal-spiiroin: so power button won't work anymore16:13
mal-Nokius: -f16:13
mal-that will follow it16:14
mal-so you can run the actual commands in a second window16:14
mal-Nokius: or --no-pager16:15
mal-that will just output the whole log and you can then scroll back16:15
Nokiusfor some reason kill is not killing my logcat16:16
spiiroinmal-: odd, did you have usb cable connected when it happened?16:16
mal-spiiroin: yes16:16
spiiroinmal-: ok, so it should not be a suspend issue.16:17
Nokiusmal-: mh journalctl -f show only xofono error also during restart16:19
*** mugna <mugna!57147c66@gateway/web/cgi-irc/> has joined #sailfishos-porters16:19
*** Tassadar_ <Tassadar_!> has quit IRC (Quit: Segmentation fault)16:20
Nokiusmal-: add a file to the gist sorry term is only have size of the screen ;)16:25
*** Lipevakala <Lipevakala!> has quit IRC (Ping timeout: 250 seconds)16:26
sledgesNokius: did you mask droid-hal-init as i asked?16:26
sledgesit shiuld not run before yu mount system16:26
spiiroinmal-: when you have time, can you check if power key events are coming or not? via "evdev_trace -t" for example (also, if you open the slider, do something on the ui and then close the slider -> display should stay on)16:27
mal-spiiroin: my mistake16:27
mal-forgot the -ini after reinstall16:27
Nokiussledges: ah I mounted and than I unmask I have to mask and mount than?16:28
spiiroinmal-: ok, that explains it - SW_LID, if left untranslated is taken to mean = the whole device or at least the screen is covered -> display can't be turned on16:28
spiiroin... .e.g. magnetic cover lid sensor in nexus5 & slidable cover in N77016:29
*** vakkov <vakkov!~vakkov@> has quit IRC (Ping timeout: 252 seconds)16:32
mal-spiiroin: now it work ok again, stupid mistake once again16:33
spiiroinmal-: np, I got a chance to refresh my memory with related logic ;-)16:33
Nokiussledges: okay is now fastboot an mask droid-hal-init16:33
mal-I really need to build a new image so that these things won't happen so often16:34
Nokiusmount /system done16:38
*** faebe <faebe!> has joined #sailfishos-porters16:39
Nokiusno hw_composer fails with = 0 again also with recompiled version16:42
piggzr0kk3rz: looking good?16:42
Nokiusalso after manual unmask and start of d-h-i16:44
mal-which line does the assert error come from?16:45
*** Tassadar <Tassadar!> has joined #sailfishos-porters16:46
*** yuit23v <yuit23v!75c8056e@gateway/web/freenode/ip.> has joined #sailfishos-porters16:47
*** vakkov <vakkov!> has joined #sailfishos-porters16:47
Nokiusmal-: 157 (I did fastboot and than umask thats wrong i shoud do umask reboot mount manual start right?) [reboot is not rebooting the device]16:48
Nokiusno is rebooted16:49
mal-I don't understand what you just wrote, but 157 means that it cannot get hwcomposer, does strace tell anything16:50
Nokiussorry of the unknowable16:51
Nokiusmal-: how I prevent that device boots into boot loader debug can't mount /system here (missing mountpoint /system)16:54
mal-when does it reboot?16:55
mal-and I don't understand what you mean by boot loader debug16:55
Nokiusmal-: may it does it coz i typed reboot (wanted to follow sledgesif mal- is right, systemctl mask droid-hal-init.service should fix23:5816:56
Nokiussledgesthen after reboot mount system and launch d-h-i manually )16:56
mal-but what is boot loader debug?16:56
NokiusWelcome to the Mer/SailfishOS Boat loader debug init system.16:57
mal-that's the way it should be16:57
Nokiusah okay was before in via 232316:57
mal-then you just continue from that to the actual system16:57
Nokiusmal-: ?16:58
mal-there should the line that says 'continue' in it when you telnet to 2316:58
Nokiusmal-: okay connection closed17:00
mal-but I have something to try: remount /system as rw if it's not, then ln -s, then start d-h-i17:00
mal-Nokius: now you should be able to telnet to 2323 after a while17:00
Nokiusmal-:  in again17:00
mal-that ln -s should be run in /system/lib/hw/17:01
Nokiusmal-:  no /system mounted (
mal-then mount it17:02
mal-do you have d-h-i masked still?17:02
Nokiushope so17:03
Nokiuslet me check17:03
Nokiusmal-: should17:05
Nokiusmal-: remount /system -o rw or including '/dev/block/mmcblk0p19'17:06
mal-if you mounted it manually did you check how it's mounted?17:07
mal-is it ro or rw?17:07
mal-at least I remount with mount -o remount,rw /system17:08
Nokiusmal-: no /system17:08
mal-so mount it17:08
mal-then check if it's rw17:09
mal-it not, remount, else create the symlink I told about before17:10
Nokius  should let me verify17:11
mal-and btw, you don't have to pastebin everything, like those mount infos, only if there is many lines with significant information17:11
mal-that looks ok17:11
mal-now the symlink in /system/lib/hw17:12
mal-you can paste small amount lines (1-3) here also directly17:13
Nokiusthe symlink is there and has the wanted stuff17:13
mal-more than that should be pastebinned17:14
mal-so if the symlink is done, then start d-h-i like you did before17:15
Nokiussh-3.2# systemctl start droid-hal-init17:15
NokiusFailed to issue method call: Unit droid-hal-init.service is masked.17:15
*** vakkov <vakkov!> has quit IRC (Ping timeout: 246 seconds)17:16
Nokiusso unmask first17:16
mal-of course17:16
mal-like you did before17:16
mal-then try EGL_PLATFORM=hwcomposer ./test_hwcomposer in /home/nemo or where ever you put that program17:19
Nokiuswidth: 1080 height: 192017:19
NokiusSegmentation fault17:19
Nokius screen turned black17:19
mal-gdb backtrace and strace17:20
locusfI get a lot of failed to allocate memory hmm17:20
locusfI finally got aries to boot sailfish but no graphics due to this17:21
locusfand everything else is broken too17:21
Nokiusmal-: strace
Nokiusmal-: sorry not all (its all from the Terminal buffer)17:22
Nokiusmal is gdb and backtrace on obs?17:22
mal-you use gdb to get a backtrace, you can install gdb if it's not installed yet17:25
*** yuit23v <yuit23v!75c8056e@gateway/web/freenode/ip.> has quit IRC (Quit: Page closed)17:25
Nokiusmh gdb is not here
Nokiussledges gave me ons a url mh let me think17:26
*** jusa_ <jusa_!> has quit IRC (Ping timeout: 244 seconds)17:26
mal-it's much easier if you set up usb-network on your device17:26
*** jusa_ <jusa_!> has joined #sailfishos-porters17:27
mal-then you can just use zypper to install programs17:27
*** vakkov <vakkov!~vakkov@> has joined #sailfishos-porters17:28
Nokiusmal-: see backlogs atm :)17:28
Nokiusfrom 4 days ago thanks :D17:28
locusf <- heres what happens in aries journal17:29
Nokiusmal-: have my eyes on it :D17:30
mal-locusf: quite strange17:30
mal-locusf: have you tried graphics with other ways than the full ui17:31
locusfmal-: test_egl results in the same17:32
mal-how eabout test_hwcomposer?17:32
locusfI don't have test_hwcomposer17:32
locusfwhich is weird17:32
mal-that's really odd17:33
mal-try to recompile libhyris and see why it does not get included17:35
*** Nokius <Nokius!> has quit IRC (Ping timeout: 240 seconds)17:35
mal-afk for a while17:37
*** Nokius <Nokius!> has joined #sailfishos-porters17:39
Nokiuszypper is doing17:41
Nokiusmal-: sorry ma dump question how to use gdb17:47
Nokiusmal-: one of my tries
Nokiuswhat Im doing wrong17:58
Nokiusah run17:59
Nokiusmal-: looks still wrong to me18:00
*** iTune <iTune!~PhompAng@> has quit IRC (Ping timeout: 244 seconds)18:10
mal-Nokius: close, you need to run bt after it crashes18:14
mal-after you start gdb type run, then wait until it segfaults, then type bt18:15
Nokiusmal-: updated gist just refresh18:15
Nokiusso some memory is missing?18:17
r0kk3rzpiggz: figuring out why it wont boot currently18:22
r0kk3rzbut at least i have eyes on it and i can see what its doing18:22
mal-Nokius: pastebin your droid-hal-$DEVICE.spec18:23
r0kk3rzseems to get reasonably far though18:24
NokiusI add the QCOM-BSP18:25
r0kk3rzi think i should probably copy in those ace configs and it might get a bit further18:26
mal-Nokius: and you used that to compile the current image? all the way from hadk 7.1?18:31
NokiusNokius: yes ( I only build a new hybris-boot.img last night)18:32
Nokiusmal-: and I edit hwcomposer18:33
*** Tassadar <Tassadar!> has quit IRC (Ping timeout: 246 seconds)18:34
mal-Nokius: you only added new hybris-boot.img?18:34
mal-well, you need to replace a lot more for the fix to be used18:35
mal-you need to install the new packages on your phone18:35
mal-just to be sure, what exacly did you do after you recompiled everything again?18:36
NokiusI build zip an 12.03 and .img last night So I have to create a new zip in best case18:38
mal-does the zip have the BSP fix already? since hybris-boot.img has nothing to do with the fix18:39
Nokiusyes it should18:39
NokiusI also edit the other file with QCOM-BSP18:39
mal-did you make a new zip after that?18:40
Nokiusiirc I asked you for douple check I did it before (sdk is all new from last weekend to now)18:40
NokiusI edit .spec on 11.03 zip is from 12.0318:42
*** gogeta <gogeta!> has joined #sailfishos-porters18:43
mal-the place where that segfault happens is the place where QCOM_BSP has effect18:44
mal-on you phone check ls -l /usr/lib/libhybris/18:45
Nokiusmal-: updated
mal-did you recompile everything completely after adding QCOM_BSP, I mean make clean or something like that before building18:50
NokiusI dit the file and than I followed the HADK18:51
Nokiusno extra stuff I edit the files before going on18:51
mal-if there is some already built libraries in the source tree then those might not get rebuilt if you make very small modification to some defines outside18:52
Nokiusokay so I all again after building the hybris-hal stuff? or also this again I'm ready to go through again18:54
mal-building libhybris and qt5-qpa-hwcomposer-plugin should be enough18:54
Nokiusokay :D18:55
mal-you can then copy those on your device and install them manually for testing18:55
NokiusI know we did that last summer from time to time :D18:55
Nokiusso what to do here18:56
NokiusI'm in MERSDK $MER_ROOT/devel/mer-hybris18:57
mal-ok, I think it's best you just do rm -R libhybris and clone it again18:58
mal-easier this way, not a nice way but works18:58
mal-the do 13.8.3 libhybris part18:59
r0kk3rzoh you should rebuild all the packages after changing the HAL?18:59
mal-changing hal?18:59
Nokiusmal-: clone is done19:00
Nokiusnow editing ?19:01
*** gogeta <gogeta!> has quit IRC (Ping timeout: 252 seconds)19:01
r0kk3rzmal: step 7.1.4 of the HADK19:02
mal-no editing needed for libhybris, since you already have edited the droid-hal-find5.spec19:02
r0kk3rzyeah cool19:02
Nokiusmal-: okay run mb219:03
mal-Nokius: we now skip the droid-hal-device building, since you said you already did that before19:04
r0kk3rzi should really find out why my device asset is failing19:05
r0kk3rzannoying to edit the script every time19:05
mal-Nokius: you don't need to run the rest of the commands, just copy the .rpm files from RPMS folder to your device19:05
mal-r0kk3rz: what is failing?19:05
r0kk3rzthe initial device check when you go to install the zip19:05
mal-ok, I don't know anything about that, I never install the zip :)19:06
r0kk3rzoh, what do you do then?19:06
r0kk3rzmaybe there is a better way19:06
Nokiusso only copying the new libhybris-*.rpm s19:07
Nokiusmal-: ^19:07
mal-Nokius: yes19:07
mal-r0kk3rz: I manually extract the .tar.bz2 to /data19:07
r0kk3rzoh right19:07
mal-not a nice way :)19:07
mal-because flashing the hybris kernel removes recovery from my device so I cannot install it unless I want to flash another kernel before that19:08
r0kk3rzoh right19:09
mal-so easier just to extract it myself and keep the hybris kernel all the time19:09
r0kk3rzyeah i'll stick with installing the zip and figure out why the assert is failing19:09
mal-I also have my /data on sdcard19:10
Nokiusmal-: copy done19:11
Nokiusmal-: zypper or rpm?19:11
mal-Nokius: then on your device install those using rpm --force -i libhybris*19:11
Nokiusmal-: running19:12
mal-then try the test_hwcomposer again, let's see if anything has changed19:13
Nokiusmal-: :,(19:14
vgradeNokius: after adding QCOM_BSP to .spec you rebuilt the hal packages19:18
vgradeand also added the hal-devel package to your target19:18
mal-vgrade: that what I was thinking, he claimed he did that before, but maybe not, since that error still exists19:19
*** Nokius <Nokius!> has quit IRC (Ping timeout: 246 seconds)19:21
*** Nokius_ <Nokius_!> has joined #sailfishos-porters19:22
Nokius_sorry network was gone19:22
mal-Nokius: go back to 7.1.1 and do everything up to 7.1.419:22
mal-including 7.1.419:23
mal-then redo what you just did for libhybris19:23
mal-including 13.8.119:23
*** corecomic <corecomic!> has left #sailfishos-porters19:23
mal-so 13.8.1 naturally before 13.8.319:24
*** dansou901 <dansou901!86820101@gateway/web/freenode/ip.> has quit IRC (Ping timeout: 246 seconds)19:29
*** Nokius_ is now known as Nokius19:31
Nokius7.1.1 - 7.1.4 (incl 7.1.4 done)19:31
mal-then 13.8.119:32
*** alin <alin!~alin@opensuse/member/ealin> has joined #sailfishos-porters19:32
Nokiusbuild libhybris atm19:36
mal-did you rm -R again?19:37
mal-then copy the rpm-files to phone again and also copy $ANDROID_ROOT/droid-local-repo/*.rpm to your phone19:39
Nokiusmal-: done with mb2 go on or copy?19:39
mal-copy, let's not create zip yet19:40
mal-testing first19:40
NokiusI assume $ANDROID_ROOT/droid-local-repo/$DEVICE/*.rpm19:43
mal-then install all files you just copied on your phone with rpm19:44
Nokiususing brain is good on my site too ;)19:44
mal-I'm drinking beer and trying to look at statefs source code19:44
Nokiusrpms on device19:45
Nokius-v may?19:46
mal-why not19:46
Nokiusso will see what happen ;)19:46
Nokiusrpm -v --force -i *19:46
Nokiusis the way or?19:47
mal-sure *.rpm maybe :)19:47
mal-just in case there's some other files19:47
Nokiusokay is an sideload folder with only the new rpms19:47
mal-then no problem19:48
Nokiuserror: Failed dependencies:19:48
Nokius        ssu-kickstart-configuration-jolla is needed by droid-hal-find5-kickstart-configuration-0.0.6-201503141926.armv7hl19:48
mal-skip that package19:48
mal-not needed19:49
Nokiusmal-: :(19:51
r0kk3rz, mal, piggz, someone19:53
mal-r0kk3rz: what happens after that?19:55
mal-Nokius: no idea why that still happens19:55
r0kk3rzmal-: after? telnet freezes and device boots into recovery19:55
r0kk3rzwhy? thats what im trying to figure out19:56
r0kk3rzim not sure whats going on with those /system issues19:56
r0kk3rzsince its the right partition number19:56
Nokiusmal-: :(19:56
mal-Nokius: continue building the rest of the zip19:57
mal-r0kk3rz: is /system mounted?19:58
r0kk3rzdidnt appear to be before i hit continue19:59
mal-second continue?20:00
mal-or first?20:00
r0kk3rzi wasnt sure if it was supposed to be mounted by then20:01
mal-so mount it manually before second continue20:01
mal-not sure myself20:01
mal-since I never used second continue20:01
vgradeNokius: can you upload your hal-devel rpm somewhere?20:02
Nokiusvgrade: o/20:02
Nokiusvgrade: sure20:02
vgradegoing to eat now but will look soon20:02
mal-that should indeed tell if the QCOM_BSP in present or not20:03
Nokiusvgrade mal- uploade done
Nokiusmal-: also the other rebuild package in 13.8.3 or only libhybris?20:06
r0kk3rzi think it booted20:06
piggzr0kk3rz: yay20:06
r0kk3rzthe screen doesnt work20:06
Nokiusr0kk3rz: \o/20:06
r0kk3rzbut it booted20:07
mal-check logs20:07
mal-vgrade: Nokius: android_config.h has #define QCOM_BSP 120:07
Nokiusso means no luck for the find5 with QCOM_BSP20:08
mal-no idea what is happening now20:09
Nokiusmal-: ? you mean further steps ?20:09
NokiusI mean how to get some light in the dark20:15
mal-well, just in case something is still wrong, it might not be bad idea to continue building the zip20:16
mal-also make sure you rebuild the qt5-qpa-hwcomposer completely20:16
Nokiusmal-: okay I will clone it due to the changes20:17
mal-maybe you could just rebould that now, from scratch and install also20:17
mal-of course you need to add the fix there20:17
NokiusI mean the 2 replace20:18
*** gogeta <gogeta!> has joined #sailfishos-porters20:18
mal-Nokius: ?20:19
Nokiuswe change yesterday a $variable with 2 in the cpp20:19
mal-that was in libhybris20:20
Nokiusmal-: oh okay20:20
Nokiusso is there a need to re clone the qt5-qpa-hwcomposer20:21
*** carepack <carepack!> has quit IRC (Remote host closed the connection)20:21
mal-Nokius: only to remove the already built studd20:22
mal-but that can be done manually also20:22
*** carepack <carepack!> has joined #sailfishos-porters20:23
r0kk3rzMar 14 21:22:05 Jolla lipstick[725]: [F] HwComposerBackend::create:74 - QPA-HWC: hw_get_module(HWC_HARDWARE_MODULE_ID, (const hw_module_t **)(&hwc_module)) in create returned -220:24
Nokiusso I will rebuild qt5-qpa-hwcomposer-plugin now20:24
r0kk3rzany ideas?20:24
mal-that suggests it does not find the hwcomposer lib20:25
Nokiusmal-: waht cm version you use?20:26
*** gogeta <gogeta!> has quit IRC (Ping timeout: 252 seconds)20:27
Nokiuswondering about line 23 in hadk-faq ( I use cm10)20:27
Nokiuswe got this today or?20:28
r0kk3rzNokius: use cm1120:28
r0kk3rzpresuming you can get cm11 for your device20:28
Nokiussure it has also 12 iirc20:28
Nokiusshal we go for cm11 will it make a huge mess now?20:29
r0kk3rzNokius: you'll have to switch branches and do a repo sync20:29
r0kk3rzand a 15gb sync later....20:30
*** piggz <piggz!> has quit IRC (Quit: Konversation terminated!)20:30
*** piggz <piggz!> has joined #sailfishos-porters20:30
Nokiusis it that worth is anyone using cm10 still20:31
Nokiusand tries QCOM_BSP20:31
mal-Nokius: I thought you use cm1120:34
mal-where is the kernel for cm10.120:34
mal-sorry, my mistake20:34
Nokiuson github ;)20:34
vgradeNokius: android_config.h in hal-devel should have QCOM_BSP define20:36
mal-looks like 10.1 does not use QCOM_BSP20:36
sledgesmal-: where did you read that out?20:37
Nokiuslets get my line burning20:37
vgradeso somethings gone amiss with a)editing the spec or building the hal20:37
Nokiuswill snapshot (hope it takes no ages)20:38
vgradesorry misread mal- comment20:38
sledgesit is using QCOM_BSP:
sledgesNokius: stay on cm10.120:38
sledgesmako is happily using it20:38
mal-board config does not have QCOM_BSP20:38
sledgesmal-: understood20:39
sledgesit does for QCOM_HARDWARE20:39
NokiusI ever wanted to test proxmox snapshot fuction :(20:39
sledgesmal-: maybe find5 is using caf gralloc?20:39
mal-sledges: it is20:39
sledgesso my link above is wrong20:40
mal-assuming it always uses display gralloc20:40
sledgesNokius: find $ANDROID_ROOT/ -maxdepth 8 -name gralloc.h20:40
Nokiussledges: /home/user/mer//android/droid/hardware/libhardware/include/hardware/gralloc.h20:41
Nokiussnapshot is started20:42
mal-the gralloc header is always there20:42
sledgesi just wonder where did i see that header wrapped in QCOM_HARDWARE instead20:42
mal-I remember something like that also20:43
mal-the last commit modifying gralloc.h20:44
sledgesif device defines _HARDWARE20:47
sledgesmaybe we should add QCOM_HARDWARE to .spec and qpa?20:47
*** piggz <piggz!> has quit IRC (Quit: Konversation terminated!)20:47
sledgesat least that wouldn't hurt20:47
mal-should not hurt20:47
*** piggz <piggz!> has joined #sailfishos-porters20:48
*** faebe <faebe!> has quit IRC (Ping timeout: 264 seconds)20:48
sledgeshas the behaviour of test_hwcomposer changed when you defined _BSP?20:48
mal-Nokius: do you have some older strace or other logs of test_hwcomposer before we added QCOM_BSP20:50
Nokiussledges added it to the wiki20:50
Nokiusdamnwas only short time paste20:51
alinsledges: did Blue... added the bug?20:52
mal-ok, there's no test_hwcomposer there20:52
Nokiusmal-: sorry than there gone20:52
mal-no problem20:53
Nokiusmal-: may one last hope20:53
Nokiuslet me check20:53
mal-I don't know how I thought you used cm1120:53
mal-it so common now to use cm1120:53
sledgesalin: nothing in my inbox..20:54
Nokiusmal-: we can try it20:55
alinsledges: ok I will add it then20:55
sledgesmal-: cm11 is not a changing factor here:
sledgesalin: much thanks20:56
vgradeNokius: can you see QCOM_BSP in your mer target tree?20:56
mal-sledges: but look at include20:56
sledgesalin: ok20:57
sledgeshow in the world would cm11 use whole bst20:57
sledgesand cm10 - not20:57
sledgesi though bsp is set fixed per hw20:58
mal-no idea :D20:58
alinsledges: so you say I am not ok?20:59
sledgesalin: absolutely :D20:59
alinsledges: the sensors bugs shall be closed i think21:00
Nokiusvgrade: ?21:00
sledgesalin: yes please, we'll open new ones case-by-case21:00
sledgesmal-: Nokius: cm11 time?....21:00
mal-sledges: I would try it21:00
sledges(just like r0kk3rz said ;)21:00
Nokiussledges: yes snapshot is done we can rallback in bad case :D21:01
sledgeswe had phones running on cm10, but they didn't have huge hwc issues21:01
sledgesmostly older phones21:01
alinsledges: i wil not close them... you have more authority21:02
Nokiussledges: it's not so young ;) I know what you mean :P21:02
mal-btw, good thing that I chose cm11, since a quite annoying wifi bug was fixed about a week ago21:02
mal-and they dropped supporting cm10.1 around the same time21:03
mal-maybe even before21:03
Nokiusokay what to do21:03
Nokiusback at 5.121:03
alinsledges: is this known... any general email I add smtp fails...21:04
mal-sledges: which is better, to get a clean android_root or change branch?21:04
alinsledges: added a (some google copycat) and while imap works... smtp  fails... added it in aandroid all is kosher21:05
sledgesalin: thanks for doing everyone a favour and closing them bugs, not...21:05
sledgesalin: not known, have you tried different providers? also worth checking with tjc21:06
sledgesas it's not hw specific21:06
sledgesmal-: clean tree side-by-side21:06
alinsledges: some poor soul
mal-Nokius: do you have enough disk space to create a new tree?21:07
Nokius5,3G free21:09
mal-much more would be needed21:09
mal-what were you talking about a snapshot?21:10
Nokiusmal-: how much more let test adding space :P21:10
Nokiusmal-: can resize disk21:10
Nokiusmal-: never tried too on proxmox21:11
mal-I'll check the size of my android_root21:11
mal-it's huge21:11
Nokiusmal-: vhost has some TB so er are safe21:12
sledges28G with compiled stuff21:12
Nokiusso more 30GB21:13
*** mugna <mugna!57147c66@gateway/web/cgi-irc/> has quit IRC (Quit: - A hand crafted IRC client)21:14
NokiusI will fasten the set belt21:14
*** Taaeem <Taaeem!> has joined #sailfishos-porters21:16
Nokiusdo we need the snapshot? It is stopping the resize21:18
sledgesno sense for a snapshot imho21:19
*** gogeta <gogeta!> has joined #sailfishos-porters21:19
*** carepack_ <carepack_!> has joined #sailfishos-porters21:21
*** carepack_ <carepack_!> has quit IRC (Client Quit)21:21
*** gogeta <gogeta!> has quit IRC (Ping timeout: 250 seconds)21:26
*** harha <harha!> has quit IRC (Quit: Leaving.)21:28
mal-sledges: QCOM_BSP is not defined in cm10.1 of my device21:30
mal-so something is really different in cm10.1 vs cm1121:31
*** gogeta <gogeta!> has joined #sailfishos-porters21:31
NokiusLets see21:37
*** Taaeem <Taaeem!> has quit IRC (Quit: AndroIRC - Android IRC Client ( ))21:38
* Nokius open set belt21:40
Nokius*smile face*
Nokiusmal-: can you give me a hand? :)21:43
sledgesbranch will now be called hybris-11.021:44
sledgesall else the same21:44
mal-and for device and kernel repos in local_manifests use cm-11.0 branches21:45
Nokiushybris get cloned21:46
sledgeswill take longer than 10.121:47
Nokiuslets see it only VDSL 50 :'(21:47
mal-Nokius: there is some additional device repos you'll need21:48
sledgestime for a good movie21:48
mal-I'm already watching one :)21:48
sledgesmal-: they'll get automagically picked as deps, no?21:48
sledgesmal-: what one if appropriate?;)21:48
MSameersledges: so 44 branch is now hybris-11.021:49
sledgesMSameer: yes21:49
MSameergood to hear21:49
mal-sledges: Chaos Theory21:49
sledgesMSameer: yep6 so everyone gets on the train;)21:49
sledgesmal-: interwesting21:50
Nokiuswhere to set the the cm11 find5 branche21:50
Nokiuscan I do this after hybris clone or at sametime?21:51
sledgesyou can do it now, and then just run repo sync again21:51
mal-Nokius: example for local manifest is in 14.3.121:52
Nokiusafter sledges hint I found it was looking before hybris clone part and confucsed21:52
Nokiuslike this only change 10.1 to 11.0 :-/21:54
r0kk3rzso long as thats the name of the branch21:56
r0kk3rzmine are all over the show21:56
Nokiuslooks like21:57
mal-the repos are: android_device_oppo_find5 (path device/oppo/find5), android_device_oppo_common (device/oppo/common), android_device_oppo_apq8064-common (device/oppo/apq8064-common) and android_kernel_oppo_n1 (kernel/opppo/n1)21:57
Nokiuskernel_oppo_n1 O.o21:58
mal-no idea why it has a different kernel21:58
Nokiusbut why n1?21:59
mal-Nokius: look at the board configs of all device repos I gave22:00
sledges23:48 < sledges> mal-: they'll get automagically picked as deps, no?22:01
sledgesdevice repo should pull the rest in22:02
Nokiusso gist is okay?22:02
mal-sledges: ok22:02
sledgesNokius: yes, let's try22:02
mal-sledges: looks like they have proper cm.dependencies22:03
mal-so should work22:03
mal-but the kernel repo is wrong in gist22:04
mal-Nokius: only add the device repo22:04
mal-kernel repo should be included22:04
* sledges starts to like oppo22:05
Nokiusso manifest is like this
*** piggz <piggz!> has quit IRC (Ping timeout: 256 seconds)22:06
mal-Nokius: that should be enough22:06
Nokiusspace gets filled :D22:10
*** Jikgxby <Jikgxby!75c8074c@gateway/web/freenode/ip.> has joined #sailfishos-porters22:10
* sledges puts a helmet on22:13
*** Jikgxby <Jikgxby!75c8074c@gateway/web/freenode/ip.> has quit IRC (Ping timeout: 246 seconds)22:14
* lpotter now knows more about android sensor stack than he wants to22:19
*** gogeta <gogeta!> has quit IRC (Ping timeout: 265 seconds)22:21
r0kk3rzlpotter: now that you have looked into the abyss, what wisdom did you divine?22:24
lpotterthere's a better way to configure them than xml22:29
Nokiusah my kernel adjustments22:42
Nokiusmal- sledges  rm or stay22:44
mal-I thought you created a new tree22:45
mal-and not use the old folder22:45
Nokiuss** than I messed up22:46
mal-well, I think it still works, just move that away22:46
mal-out of the android_root22:46
Nokiuswht the kernel/oppo/find folder22:48
mal-just the find5 folder is enough22:48
Nokiuserror: hybris/hybris-boot/: mer-hybris/hybris-boot checkout 4cdb7074786b39c9174673aad02092a9010cc5e422:54
Nokiusmal-: so the mess is done ^ ?22:59
mal-might be23:02
mal-I don't know enough of how repos work, sledges?23:03
r0kk3rzNokius: presumably you already checked out the cm10.1 repos?23:09
NokiusI had yes23:09
r0kk3rzthen maybe you might have to go through and do a repo init -b cm11.023:10
Nokiusfatal: Couldn't find remote ref refs/heads/cm11.023:11
r0kk3rzwhat dir are you doing that in23:12
r0kk3rzalso, you can rm the device dirs23:12
*** ro <ro!> has quit IRC (Remote host closed the connection)23:13
r0kk3rzthe dirs specified in your manifest23:13
Nokiusrm device done23:13
r0kk3rzpretty sure thats all i did when switching from cm10 to cm1123:14
Nokiusr0kk3rz: waht you mean with dirs in manifest23:15
Nokiusr0kk3rz: both are removed23:16
Nokiusstill head error23:16
r0kk3rzdoing a sync?23:16
vgradeNokius: just wanted to be sure the hal-devel got installed into your target for building hybris butI see you moved on23:17
Nokiusvgrade: yes ...23:17
vgradeno probs, was a long shot anyway23:18
Nokiuslets see if cm11 helps23:18
Nokiusr0kk3rz: still23:19
vgradejust I remember piggz had an issue with those defines not being taken23:19
Nokiusremoving $ANDROID_ROOT? and redo23:19
Nokiussince I did npt start a new tree it is a mess or?23:20
r0kk3rzyou can nuke the android root and start again23:21
r0kk3rzheh wrong branch name on that repo init command23:22
r0kk3rzmaybe thats why it didnt work23:22
r0kk3rzmissing -23:22
mal-why would you want cm-11.0 ain not hybris-11.023:23
r0kk3rzmal i think sledges recently branched hybris-11 to cm-1123:25
Nokiusand again sync23:25
sledgesNokius: did you delete all of your old ANDROID_ROOT?23:26
Nokiusyes a few minutes ago :-/23:27
sledgesrepo init ... hybris-11.023:27
sledgesrepo sync23:27
sledgesand goodnight ;)23:27
Nokius:D is running23:28
Nokiussledges: gn823:28
Nokiuswatching network grapphs again :D23:29
*** r0kk3rz <r0kk3rz!> has quit IRC (Ping timeout: 246 seconds)23:41

Generated by 2.17.1 by Marius Gedminas - find it at!