| Oksana | When I plug in Fxtec Pro1 to computer, it is shown in lsusb as Qualcomm, Inc. Gobi Wireless Modem (QDL mode). So, Something is alive here still. But, how do I get it to charge properly? | 01:47 |
|---|---|---|
| Oksana | No, fastboot devices doesn't see it. | 01:48 |
| Oksana | msm8998 | 01:50 |
| r0kk3rz | fastboot wont work unless the device is in fastboot mode | 02:57 |
| r0kk3rz | what state is the device in? booted up? | 02:57 |
| Oksana | The device is in black brick state. Aka, run out of battery, would not charge, would not switch on, would not do anything. Qualcomm modem does show up, though, as lsusb shows. | 03:04 |
| r0kk3rz | ah ok | 03:05 |
| r0kk3rz | maybe act dead mode doesnt work properly on that yet | 03:05 |
| r0kk3rz | i would plug it into a real charger and leave it for an hour | 03:05 |
| Oksana | dmesg says new high-speed USB device number 58 using ehci-pci ; New USB device found, idVendor=05c6, idProduct=9008 | 03:06 |
| Oksana | New USB device strings: Mfr=1, Product=2, SerialNumber=0 ; Product: QUSB__BULK ; Manufacturer: Qualcomm CDMA Technologies MSM | 03:06 |
| Oksana | qcserial :1.0: Qualcomm USB modem converter detected ; Qualcomm USB modem converter now attached to ttyUSB0 | 03:06 |
| Oksana | r0kk3rz: I had it plugged into its real 5V 3A charger for whole night. | 03:06 |
| r0kk3rz | hmm ok | 03:07 |
| r0kk3rz | try and boot it up with it connected to a charger? | 03:07 |
| Oksana | Did try. Just power button, or power button with volume up, or power button with volume down... | 03:07 |
| * Oksana is now apt-upgrading laptop from ASCII to Beowulf, just to get Qt5.9+ instead of Qt5.7, just to get Sahara running ( https://github.com/openpst/sahara ), just in case Sahara knows how to communicate with QDL mode... | 03:09 | |
| r0kk3rz | not sure thats going to help you | 03:09 |
| Oksana | Not sure either. I think that if I disassembled the device and charged up the battery, then all would be well (till next flat-battery time). But, I have no idea how to disassemble it. | 03:10 |
| Oksana | Well, I could start with disassembling the display, it seems to have lots of screws, but that seems to be way too fragile and out of the way. | 03:11 |
| r0kk3rz | i wouldnt do that, id talk with chen about it first | 03:11 |
| Oksana | I wouldn't disassemble it either. Talk with Chen... Would be nice. | 03:11 |
| r0kk3rz | he is fairly active in the fxtec thread on tmo | 03:13 |
| r0kk3rz | http://talk.maemo.org/showthread.php?t=100554&page=336 | 03:13 |
| r0kk3rz | but leave it plugged into a pc in qdl mode, maybe it slow charges the battery | 03:14 |
| Oksana | Hmm, alright. Not sure for how long it is plugged into the laptop in QDL mode, but will leave it as it is for a few hours. | 03:18 |
| T42 | Beverly Core %lastname% was added by: Beverly Core %lastname% | 05:32 |
| piggz | Oksana: that rings a bell | 07:21 |
| piggz | Oksana: QDL tool might help, i found you had to start qdl, unply usb, plug usb | 08:01 |
| piggz | mal: https://pastebin.com/8W92i4s1 | 08:12 |
| vknecht | @Oksana: this thread seems related (read entirely before attempting anything): https://community.fxtec.com/topic/2559-factory-restore-tool/ | 08:29 |
| vknecht | iirc it might also be necessary to disable Linux distro NetworkManager service when dealing with EDL/QDL | 08:30 |
| *** Mister_Magister is now known as Mister_Magister_ | 09:03 | |
| *** Mister_Magister_ is now known as Mister_Magister | 09:03 | |
| *** Oksana_ is now known as Oksana | 09:08 | |
| T42 | <alexisrev> I started earning the day I took the courage to invest in Bitcoin with Amos Bauer , now I'm glad I took that courage. I just got $5500 profits sent directly to my PayPal account. | 09:39 |
| T42 | <alexisrev> https://t.me/joinchat/AAAAAEeKU6Sw5GH9jOA7Yw | 09:39 |
| T42 | <polanobi> @alexisrev [I started earning the day I took the courage t …], report | 09:42 |
| piggz | mal: so, the assertion in pulse comes from https://git.sailfishos.org/mer-core/pulseaudio-modules-nemo/blob/master/src/mainvolume/module-meego-mainvolume.c#L1424 | 11:09 |
| piggz | pactl set-sink-volume 0 +10% works as expected | 11:09 |
| piggz | so, need to figure out why the above function is passing invalid data | 11:09 |
| piggz | where is jusa when u need a PA problem fixed | 11:10 |
| T42 | <NotKit> Oksana, is your host on Linux? | 11:14 |
| piggz | @notkit i believe so | 11:14 |
| T42 | <NotKit> another possibility may be to reflash with Linaro https://www.96boards.org/documentation/consumer/guides/qdl.md.html and firmware from https://drive.google.com/open?id=1HjONRqxw5NaTimty_54TKkZK4wNF-sps | 11:15 |
| T42 | <NotKit> sudo ./qdl --storage ufs prog_ufs_firehose_8998_ddr.elf rawprogram_8998.xml patch_8998.xml | 11:17 |
| T42 | <NotKit> will erase everything, but should bring it out of brick state | 11:18 |
| piggz | mal: this prevents crash, but doesnt fix problem https://git.sailfishos.org/piggz/pulseaudio-modules-nemo/commit/207c79b1a9b4a3927e88b16c0fa5783c5c605447 | 12:49 |
| T42 | <Akatsu39> is there any sheet with syscall names? i have kernel errors with "syscall 384 | 20:36 |
| T42 | <Akatsu39> " | 20:36 |
| T42 | <Akatsu39> How can i find if SELINUX is enabled? when i grep for SELINUX in journalctl -b i get +AUDIT +SELINUX | 20:52 |
| T42 | <elros34> search for selinux: disabled at boot or something like that in dmesg/journal | 21:34 |
| T42 | <meierrom> @polanobi: guess you better ping @Thaodan for this channels daily spam ;) | 22:30 |
| T42 | <polanobi> (Sticker, 512x512) https://irc.thaodan.de/.imgstore/mgRCbkfAui.webp | 22:30 |
| evelyn | I'm trying to test sb2 as directed in the porting guide. I created the simple main.c, and tried to run the command... sb2 -t $VENDOR-$DEVICE-$PORT_ARCH gcc main.c -o test | 23:23 |
| evelyn | However, it says no such file or directory. When chrooting into it, it seems that the current directory (where my ANDROID_ROOT is) isn't mounted in the chroot it creates. | 23:23 |
| evelyn | and subsequent attempts to build my device's packages fails I think for the same reason. It's not clear to me where to start debugging this. | 23:25 |
| r0kk3rz | show the full output | 23:25 |
| mal | are you sure you used the correct target name when you created the target? | 23:25 |
| r0kk3rz | and double check your variables are correct | 23:25 |
| evelyn | well... it's complicated | 23:31 |
| evelyn | but here is a paste: | 23:31 |
| evelyn | https://paste.debian.net/hidden/3e5e3f6c/ | 23:31 |
| evelyn | I ended up with several layers of /opt/build.. I suspect it's because my ANDROID_ROOT isn't my home directory. But I don't have room in my home directory. | 23:32 |
| r0kk3rz | thats ok, it doesnt need to be | 23:33 |
| evelyn | The target's definitely correct. I can compile things inside the target fine | 23:33 |
| evelyn | it's slightly confusing what I ended up with. | 23:33 |
| piggz | mal: did you see my patch earlier? | 23:39 |
| piggz | s/hack | 23:40 |
| evelyn | I'm honestly thinking that the only thing I've done wrong is not set ANDROID_ROOT to be somewhere in my home directory.. :( | 23:58 |
| r0kk3rz | thats never been an issue in the past | 23:59 |
| r0kk3rz | and irrc sb2 doesnt do anything with that variable anyway | 23:59 |
Generated by irclog2html.py 2.17.1 by Marius Gedminas - find it at https://mg.pov.lt/irclog2html/!
